#REQUEST.pageInfo.pagedescription#

Site Navigation

MANU6006 - REVIT Introduction

banner1
Title:REVIT Introduction
Long Title:REVIT Introduction
Module Code:MANU6006
 
Duration:1 Semester
Credits: 5
NFQ Level:Fundamental
Field of Study: Manufacturing Engineering
Valid From: Semester 1 - 2016/17 ( September 2016 )
Module Delivered in 6 programme(s)
Module Coordinator: NIALL MORRIS
Module Author: WILLIAM BATEMAN
Module Description: This module has been developed to introduce the learner to Autodesk REVIT Software by working with architectural, structural and MEP systems (mechanical, electrical and plumbing) details in buildings.
Learning Outcomes
On successful completion of this module the learner will be able to:
LO1 Draw common engineering details for building construction.
LO2 Use standard design methodologies to contribute to the design of building elements.
LO3 Use industry standard software to communicate engineering information to other technically qualified personnel.
LO4 Produce hardcopy drawings and reports using industry standard software
Pre-requisite learning
Incompatible Modules
These are modules which have learning outcomes that are too similar to the learning outcomes of this module. You may not earn additional credit for the same learning and therefore you may not enrol in this module if you have successfully completed any modules in the incompatible list.
No incompatible modules listed
Co-requisite Modules
No Co-requisite modules listed
Requirements

This is prior learning (or a practical skill) that is mandatory before enrolment in this module is allowed. You may not enrol on this module if you have not acquired the learning specified in this section.

No requirements listed
Co-requisites
No Co Requisites listed
 

Module Content & Assessment

Indicative Content
Setting Out.
Setting out and placing of grids and levels, foundation details, structural columns,( beams, trusses, braces ).
Views.
Generation of plan views at all levels, sectional views. Duplicating and renaming of views.
Fabric elements
Sourcing and inserting walls, windows, curtain systems, doors, floors, roofs, U-values, false ceilings. Revit seek.
Stairs and openings
Generating wall and shaft openings. Inserting ramps, stairs, railings.
Tagging
Room and area tagging
Components.
Sourcing and inserting plumbing fixtures, lighting fixtures, furniture. Revit seek.
Schedules.
Generating schedules of components and fabric elements.
Printing.
Set up and printing of sheets and schedules.
Assessment Breakdown%
Course Work100.00%
Course Work
Assessment Type Assessment Description Outcome addressed % of total Assessment Date
Practical/Skills Evaluation Class material to date 1,2,3,4 20.0 Week 4
Practical/Skills Evaluation Class material to date 1,2,3,4 30.0 Week 7
Project Draw and fit out of mechanical, electrical and plumbing services for a commercial building. 1,2,3,4 50.0 Sem End
No End of Module Formal Examination
Reassessment Requirement
Coursework Only
This module is reassessed solely on the basis of re-submitted coursework. There is no repeat written examination.

The institute reserves the right to alter the nature and timings of assessment

 

Module Workload

Workload: Full Time
Workload Type Workload Description Hours Frequency Average Weekly Learner Workload
Lab Practical based instruction 4.0 Every Week 4.00
Independent & Directed Learning (Non-contact) Self directed learning 3.0 Every Week 3.00
Total Hours 7.00
Total Weekly Learner Workload 7.00
Total Weekly Contact Hours 4.00
Workload: Part Time
Workload Type Workload Description Hours Frequency Average Weekly Learner Workload
Lab Practical based instruction 3.0 Every Week 3.00
Independent & Directed Learning (Non-contact) Self directed learning 4.0 Every Week 4.00
Total Hours 7.00
Total Weekly Learner Workload 7.00
Total Weekly Contact Hours 3.00
 

Module Resources

Recommended Book Resources
  • Eric Wing, 2012, Autodesk Revit Architecture 2013 [ISBN: 9781118255940]
Supplementary Book Resources
  • Department of Environment 2012, Technical Guidance Document A, Structure Ed. [ISBN: 9781406427028]
  • Department of Environment 2008, Technical Guidance Document G, Hygiene Ed. [ISBN: ISBN NOT ALLOCATED]
  • Department of Environment 2010, Technical Guidance Document H, Drainage and Waste Disposal Ed. [ISBN: 978-1-4064-2338-9]
This module does not have any article/paper resources
Other Resources
 

Module Delivered in

Programme Code Programme Semester Delivery
CR_EBENS_8 Bachelor of Engineering (Honours) in Building Energy Systems 3 Elective
CR_ESENT_8 Bachelor of Engineering (Honours) in Sustainable Energy Engineering 3 Elective
CR_EBSEN_7 Bachelor of Engineering in Building Services Engineering 3 Elective
CR_ECTMS_7 Bachelor of Science in Craft Technology - Mechanical Services 3 Mandatory
CR_EMEPB_7 Certificate in Mechanical, Electrical and Plumbing BIM Applications 1 Mandatory
CR_EBSEN_6 Higher Certificate in Engineering in Building Services Engineering 3 Elective

Cork Institute of Technology
Rossa Avenue, Bishopstown, Cork

Tel: 021-4326100     Fax: 021-4545343
Email: help@cit.edu.ie